Search:

Geti titanium sells rings, but also offers a laser engraving service. Dennis

https://getititaniumrings.uk/

Foredom are based in the USA, but they have been known to help UK customers in the past:

https://foredom.net/contact-foredom-electric-co/

Ultimately if expense is involved, you will need to...

I don't have one, but looking at the instructions:

https://foredom.net/wp-content/uploads/handpc_instructions/20_20D_20SJ.pdf

It might be possible to remove the nose cone, release the lever,...

Any rotary tool and a twist drill, but if you don't have them, then something like this might do:
...

A simple way out of this is to drill an appropriate hole (about 2mm), and thread and close a jump ring so stout that it does not need soldering.
6-7 mm diameter made of 1.5mm wire would do.
...

Hi Bev,
I'm not into melting and casting, but I know that you will need a really hot torch, and which you get depends a lot on your budget, and possibly your insurer.
Watch this space and members...

It's a picture of a chain. If you log on you can open it

Various ways with jump rings, showing what can be done.

No need for that David. You need to melt the solder more slowly, using a gentle flame. Make sure the ends of the jump ring are in close contact, or they will shrivel apart.

For closing single jump...

That has been a regular topic over the years, with never any clear solution. One thing is certain: You will get the blame for apparently passing off inferior metal.
If none of your guesses solves...

That's a cock eyed idea if ever was and the road to permanent injury. Jewelry quality solder melts at 675 degrees Celsius at its lowest, and soft solder at around 300.

You might succeed with a...

You're supposed to be able to fuse Argentium, but I have had trouble seeing whether the fusion is successful. If you go on heating, it is liable to shrivel up, so to avoid hassle, I added a little...

Hi Indi, and welcome back. Chains made with Argentium are beautiful and white. You just have to bear in mind that this version of silver can't stand disturbing in any way while glowing red, or it...

All these different opinions are the whole point of the forum of course.
Auflux has been my go to, even for large pieces like belt buckles, but it does get exhausted more quickly than borax. So it...

Most of the time when attempting to visit the Forum, I get 'Content encoding error'.

I am hoping that Dave will see this and come to the rescue. Dennis.

Once I've gone through the routine it's good enough for me.

That said I don't use fluxes that leave a hard to dissolve glaze behind.
For me paste solders are messy, so I use snips of strip...

Try your usual pickle first. If unwanted residues still remain,m then use safety pickle followed by a hot bicarbonate of soda solution, and then rinse in plain water.. Dennis.

Dear Steph,

I thought I might pick up on some of your points, in case my comments help you to improve your finish.

1. Brass brushes should always be used wet and soapy, or they will deposit a...

Well, there you are. Someone could say 'all worried for nothing', but you will be much better prepared when it crops up again.

First decide on your priorities.

If you don't wish to loose the client, explain that you will have a go, but if a split appears, you will provide a new base at your or her expense.

As you wont...

Yes, you are right. Silver arrives smooth and undamaged, so work in a clean area, and with a painters brush, get rid of filings which would scratch your work.
Use soft tools guarded with nylon, or...

Well that is a sad and unusual drama, just about pliers.
I'm sorry you had all this trouble, and hope that the prestige version will serve you for life. They are a good price too.
Thank you for...

I'm glad it's working for you. Of course in my day they didn't have the posh draw tongs.
It would be really good if you could post a picture eventually. Dennis

Any one from Cookson will probably do you Sheena. After all they are easily adjusted by pushing the two scrolls closer together by hand.
...

Thank you for your feedback. Best wishes to your daughter. Dennis.